非标自动化设备在验收过程中有哪些细节要注意?

发布时间:

2023-02-10 11:28

  非标自动化设备的构思、设计、定制等一系列的规划都需要认真完成, 最后的验收工作也十分重要。那么对于消费者而言在非标自动化设备验收的环节有哪些细节需要注意呢?
  The conception, design and customization of non-standard automation equipment need to be carefully completed, and the final acceptance work is also very important. So for consumers, what details need to be paid attention to in the acceptance of non-standard automation equipment?
  验收设备性能是否稳定?
  Is the performance of acceptance equipment stable?
  工作效率能否达到预期?
  Can work efficiency meet expectations?
  操作是否便利?
  Is the operation convenient?
  是否符合设备制造的安全规范等买卖双方协议的要求?
  Whether it meets the requirements of the agreement between the buyer and the seller, such as the safety specification of equipment manufacturing?
非标自动化设备验收细节
  另外更加细致的工作,就是对于设备的一些细节部分的质量做好考核,像设备中焊接件的验收。
  In addition, more detailed work is to check the quality of some details of the equipment, such as the acceptance of welding parts in the equipment.
  常规来说,焊缝必须到达GB50205-2001钢结构工程施工验收规范中规定的《三级焊缝的验收规范》,部分非标需到达国家规定的二级焊缝规范。
  Generally speaking, the weld must reach the "code for acceptance of class III weld" in the code for acceptance of steel structure engineering construction (GB 50205-2001), and some non-standard welds must meet the national secondary weld code.
  按照图纸对照相关管口方位和地脚螺栓中心距,对相关设备焊缝检查有无突出太多,容器不圆度多少等等。
  According to the drawing, check whether there is too much protrusion on the welding seam of the relevant equipment and the out of roundness of the container according to the relevant pipe mouth orientation and anchor bolt center distance.
  还有需要检验非标自动化设备的制作钢材质量,对全部钢板应作超声波探伤检查,22mm以下的钢板,要取钢板数量的10%进行“米”字形超声波探伤检查。如发现有缺陷,应重新对全部钢板进行检查。
  In addition, it is necessary to inspect the quality of steel produced by non-standard automation equipment. Ultrasonic flaw detection should be carried out on all steel plates. For steel plates below 22mm, 10% of the steel plates should be taken for "meter" ultrasonic flaw detection. If defects are found, all steel plates shall be inspected again.
  在检查验收钢板时,看表面是否光滑平整,不得有气泡、结疤、坡口边不得有夹层、裂纹等缺陷。
  When checking and accepting the steel plate, check whether the surface is smooth and flat, and there are no bubbles, scabs, interlayer and cracks on the groove edge.
  以上各环节确认之后,就需要在非标自动化设备正常工作的过程中进行检查,出现任何问题要及时反馈技术工程师。只有非标自动化设备的整个环节顺畅之后,才能正常投入使用。
  After the above links are confirmed, it is necessary to check the non-standard automation equipment in the normal operation process, and any problems should be timely fed back to the technical engineer. Only after the whole link of non-standard automation equipment is smooth, can it be put into use normally.

非标自动化设备